![]() I don't think that's the case with the models of 2850, but if it was you would see an option in the BIOS to enable this. To use VMDirectpath on an Intel Server chipset used must support Intel VT - d (Directed i/o). This will solve my problem or is this server too old for passthrough to work? So, I was thinking of buying this one ( Adaptec 39320) because he seems to be on the list. This is probably why passthrough doesn't work. Also, I noticed that my SCSI controller card is NOT on the HCL ( Adaptec 39160). Under Configuration > storage adapters > I don't see my tape drive listed. I get this error under VMDirectPath, 'host does not support configuring passthrough ". I'm trying to get a tape backup to work on my ESXi host, so I can save my win2003 VM. In the 2850 processors do NOT support the VT, then you would be very limited with virtualization options.ĮSXi 4.1 - Dell Poweredge 2850 - tape backup - host does not support configuring passthrough Management system - software of management of Dell is NOT supported on the client OS. ![]() Keep in mind that server (such as 16 MB video memory) graphics will run NO Aero or high resolution/refresh.ĭRAC - if you have a DRAC (Dell Remote Access Controller) card installed, you will not be able to install drivers to meet these devices in Device Manager. Graphics - you should probably use the drivers of graphics/video 2008 x 64 for a decent resolution. Chances are that Windows 7, like server 2008R2 will NOT have the drivers for the controller RAID (PERC 4e/Di), so use the driver 2008R2 for the RAID controller (and any other device requiring disks after installation).Ĭontroller RAID PERC 4e/Di to 2008R2 driver:Īlso keep in mind that PERC does NOT support non-RAID, so you MUST configure RAID before installing, or even with the right driver, no hard drive is visible. Stick the DVD in the drive and start to install. Windows XP is an option, but I'd rather not, if I have to I understand that they are not made for the server, but I would use Windows 7 instead of the server operating system. I was wondering how I could go about the installation of operating system, including Windows 7 and Windows XP on my server. Install a non-of a Dell Poweredge 2850 server operating system Take a look at can not power on a 64-bit Windows VM Usually not enabled virtualization technology in host BIOS. When I start up a virtual computer, it gives a wrong message shown in the picture below. It shows lm, long mode, so you can run 64-bit, that you are running ESX, but to succeed in this 64-bit support, you need the lm, you and vt, which you don't have.Ī Dell PowerEdge 2850 server is used for the new ESXi server, but it does not support the 64-bit VM. The output of the processor shows the same thing, or rather, what he shows no vt in its ability. The dell series 8 (1850/2850) have no vt support, so not support 64-bit virtual machine, except 6850. It seems obvious to me that the PowerEdge 2850 works well with the 64 bit OS but not ESXi 4.1. Now the question I have is this: given that VMWare is problems with 64-bit OSes comments, how is it that I can install CentOS 5.5 64 bit on this Dell PowerEdge 2850 with no problems. Longmode is disabled for this virtual machine. However, the 64-bit mode is not possible. :This veritual is configured for 64-bit operating systems. During the installation of a VMware instance, I get this: Then, I created a few instances VM I want to install CentOS 5.5 64 bit. I then installed VMWare ESXi version 4.1 on the Dell Poweredge 2850 with no problems. This box was initially installed with Redhat Linux ES 5.4 64-bit and OS 64 bit CentOS 5.5 with no problems, so I know the processor supports 64-bit. I have a Dell PowerEdge 2850 with 12 GB of RAM and two CPUs, hyperthreading with 350 GB of disk space. The installation went perfectly fine afterwards. I made another copy of the disc, this time burning the CD at a 4 x speed. I had hard time to install a CD earlier which worked perfectly well on another machine. Some of the Dell CD-ROM may be little flighty. The inventory number of Dell on the machine is 6HDGS81 Now, I read on a few different posts within the VMware communities that some people have had luck with this question and others did not. I tested it on another machine has worked like a champ. My next thought was that there was something wrong with the ISO image that I downloaded. But all I see is the first line of text of the CD which is the following: Here are the latest versions of firmware available from Dell on this box. This is all what I've updated in what concerns the firmware on the box today. My first thought to solve this problem was the BIOS. The server works very well with Windows 2000 server. ![]() I have a Dell PowerEdge 2850, who does not start on a CD of VMware ESXi 3.5. Dell PowerEdge 2850 does not start on a CD of ESXi 3.5
0 Comments
Leave a Reply. |